|
TOGGLE
CARS
1-1/4" &
1-1/2"
(For
offshore
poles)
This car
slide is
offered
both in
stainless
steel
and hard
coat
anodized
extruded
aluminum.
The
toggle-pin
is
stainless
steel in
each
case.
Our
strong
1.500"
toggle
spinnaker
car is
for
boats
approx.
50' to
70' LOA.
Fits the
standard
Schaefer
41-12
1.500"
track.
Low
friction
movement
due to
UHMW
inserts.
 FOR
POLES
WITH OUR
TS & UTS
END
FITTINGS,
AND
USING A
FORESPAR®
T-125-S
CAR, 3"
IS
SUBTRACTED
WHEN
GIVEN A
"J"
DIMENSION
TO
ESTABLISH
POLE
LENGTH.
To
allow
vertical
storage
on the
mast of
larger
poles up
to 6"
diameter,
specify
our long
toggle
option.
Our
standard
toggle
works
with
poles to
4.500"
diameter.
| Part No. |
Model No. |
Track Size |
Retail |
| 333004 |
T-125-S (s/s body) |
1.250" |
$456.00 |
| 333020 |
Long Toggle Option |
|
$257.50 |
| 333010 |
Toggle & Knuckle Assembly |
|
$214.25 |
| 334002 |
AT-125-S (aluminum body) |
1.250" |
$325.00 |
| 334100 |
AT-150-S (aluminum body) |
1.500" |
$779.00 |
| 331013 |
Replacement Runners |
|
$18.50 |
|
|
|
| 
MAST CAR & PAD EYE RING DIAMETER
Many masts on boats built through the 70's and early 80"s came with mast pad eyes or ring cars for attachment on the spinnaker pole. These were fixed eyes or sliding cars with relatively small ring diameters. Some were as small as 1.000" I.D.
Forespar® "ULTRA" series end fittings (both the UXP and UTR style) require a minimum of 1.500" I.D. rings for proper function. If the ends are used on rings less then 1.500" I.D. the jaws ("beak") can bind-up in the rings and with the leverage of an 8' pole, (or longer!) the ends will fail.
 This is not the fault of the end fittings. A proper sized ring will avoid this and allow the ends to freely move under spinnaker pole compression loads as needed.
Forespar® offers S/S mast pad eyes (PE-3-SF & PE-3-SC) and sliding ring cars (RC-125) with 1.625" I.D. rings for use with our end fittings. Lesser diameter rings should be changed-out to avoid potential failure to ends due to insufficient clearance. Forespar® will not warrant ends that fail due to improperlysized rings on the mast.
|
|
 RING
STYLE
MAST CAR
- RC 125
The
ring and
body of
this
unusually
strong
car is
investment
cast of
17-4
heat
treated
stainless
steel to
provide
a
superior
product.
Compatible
with our
"UXP"
and "UTR"
pole end
fittings.
Ring
I.D. is
1.625".
The
RC-125
is for
1.250"
T-track
and has
a screw
lock-pin,
our
special
UHMW
polyethylene
slides
inserts
and
provisions
for up
and down
shackles.
RC-125
car is
NOT
recommended
for use
with
poles
that are
to be
stored
vertically
up the
mast.
| Part No. |
Model No. |
Retail |
| 331000 |
RC-125 |
$87.00 |
|
|